NF Mighty NF forum 2016x>


Author Topic: Tool Box keys-source...  (Read 213 times)

David Gilli

  • Newbie
  • *
  • Posts: 16
    • View Profile
Tool Box keys-source...
« on: November 22, 2015, 05:32:16 pm »
Hello,
 Further to earlier mention, I think i have found the tool box keys available from lockdoctor.biz under Metal filing cabinet key in the range of 92001-92400...
Search box on the site.
I have not yet looked closely to see if the number is on the outside of the locks.
The two are different numbers from each other.
  I see they sell the locks too in case you need them.
Apparently three numbers  in the range of 001-400 would be on the lockface.....(ie.last three numbers).my keys end in 90 and 99 and all the 5 numbers are on the key.
Worked out 7.14 total for the two incl. delivery. So we are talking about cut keys here, not just blanks. I hope this is useful to someone.
Best to all.

Social Buttons


Bruno

  • Full Member
  • ***
  • Posts: 113
    • View Profile
Re: Tool Box keys-source...
« Reply #1 on: November 23, 2015, 06:10:31 pm »
I bought two complete locks with two keys each,from eBay.Listed as you say,as locker locks.
I had to buy complete locks as a previous owner had bodged on some bolts instead of locks.I think I paid about 10 for both.

banquo

  • Administrator
  • Hero Member
  • *****
  • Posts: 721
    • View Profile
Re: Tool Box keys-source...
« Reply #2 on: November 28, 2015, 12:10:20 pm »
Mine came with brand new locks and 2 keys, but although they work well enough, the lock is far smaller than the original. I got a pair of original ones with some Serbian spares, and the lock faces are much larger in diameter, and brassy looking, instead of the chrome that came on mine. If you're not a slave for originality, the locker ones seem to do the job.

patentgeek

  • Newbie
  • *
  • Posts: 28
  • Nuovo Falcone in San Francisco, California
  • Location: San Francisco, California
    • View Profile
Re: Tool Box keys-source...
« Reply #3 on: August 06, 2017, 07:14:44 am »
Direct link to the lockdoctor.biz page:

https://www.lockdoctor.biz/product/001-400-lf-england-eurolock-baton-key/

But ordering these requires knowing the last 3-digits of the key code number, and unlike the ignition key, the key code is not stamped on the tool box lock face.

What to do if the key code is unknown?


OldeGoat

  • Jr. Member
  • **
  • Posts: 83
    • View Profile
Re: Tool Box keys-source...
« Reply #4 on: August 06, 2017, 08:03:45 am »
I bought a pair of locks from eBay which were for a Royal Enfield. Not as nice as the originals, the lever needed bending a bit but they work.
Less than 10GBP if I recall.

patentgeek

  • Newbie
  • *
  • Posts: 28
  • Nuovo Falcone in San Francisco, California
  • Location: San Francisco, California
    • View Profile
Re: Tool Box keys-source...
« Reply #5 on: August 06, 2017, 05:52:05 pm »
I'm not inclined to replace the original locks if they are working okay.

Does anyone have the manufacturer and part number for a key blank that will fit the original locks? If I can get blanks, my local locksmith can cut a key to fit the lock.

cloggy

  • Jr. Member
  • **
  • Posts: 80
    • View Profile
Re: Tool Box keys-source...
« Reply #6 on: August 18, 2017, 11:51:23 pm »
I just ground the tips of some bigger keys thinner. Took three minutes.